- 1 How do I use Eka code?
- 2 How do you get the EKA code on Discovery 2?
- 3 How do I reset my Immobiliser on my discovery 2?
- 4 How do you code a Range Rover key?
- 5 How do I bypass 300tdi Immobiliser?
- 6 What is a Nanocom?
- 7 How do I bypass immobilizer?
- 8 Where do I find my emergency key access code?
- 9 How do I reset my Freelander immobiliser?
- 10 How do I turn off my discovery 1 Alarm?
- 11 How do you turn off the alarm on a Land Rover Discovery?
How do I use Eka code?
To use an EKA code to disarm a vehicle, perform the following sequence: Insert the key into the drivers door lock and turn to the lock position. Wait for 5 seconds. Turn the key to the unlock position the number of times indicated by the first digit of the EKA code.
How do you get the EKA code on Discovery 2?
The EKA code is found on the security information card supplied with your vehicle. The code is 4 digits long. The EKA code IS NOT the code in the key fob. The grey plastic tag on the keys IS NOT the EKA code, it is the ignition key code.
How do I reset my Immobiliser on my discovery 2?
Immediately open the door, insert the key in the ignition switch and turn the switch to position II. If the ignition switch is not turned to position II within 30 seconds of the end of the 5 minute wait, the engine is automatically immobilised again.
How do you code a Range Rover key?
How to Program Your Land Rover Key Fob: Step by Step
- Stand outside the vehicle with all doors closed.
- Rotate the key inside the door lock as far as it will turn for three seconds.
- Let go of the “Lock” button once your key is out of the door.
- Your key fob and Land Rover vehicle will now be fully synchronized.
How do I bypass 300tdi Immobiliser?
run a wire from the starter solenoid (leave the original in place) into the footwell in the drivers side, remove the plastic acess pannel, find the starter relay, find thick brown/red wire and connect into it. The immobiliser disables both the fuel solenoid and the starter motor.
What is a Nanocom?
Custom Remap for the TDV6 – EMS Flash File [NANOCOM] A custom VBF Remap file that can be programmed into the engine management using our diagnostic server based systems applicable to Discovery 3 / LR3 or Pre 2010 Range Rover Sport with a TDV6 Diesel Engine. The file is provided via Blackbox Solutions
How do I bypass immobilizer?
You can bypass the immobilizer by placing the key in keyhole hence deactivating the car’s immobilizer to remote start. The added security with Mobokey allows the security to be activated as soon as the phone moves away from the car, so you don’t have to worry about car security.
Where do I find my emergency key access code?
Emergency Key Access Code. The EKA code is found on the security information card supplied with your vehicle. The code is 4 digits long. The EKA code IS NOT the code in the key fob.
How do I reset my Freelander immobiliser?
Blip your landy and unlock it. Sit there for 30 seconds without putting the key in or near the ignition. When the immobiliser light starts flashing again to say it has armed put the key fob to the top of the ignition barrel. The light will go out.
How do I turn off my discovery 1 Alarm?
Unlocking it is simple, unlock/lock three times with the key in the drivers side door. That disables the alarm and you should hear two beeps of the horn and the turn signals should flash twice to confirm. Not a big deal.
How do you turn off the alarm on a Land Rover Discovery?
To disarm the alarm, press the unlock button on the Smart Key or press the START STOP button with the Smart Key inside the vehicle. Single-point entry allows only the driver’s door to unlock with a single press.